Enterprise name: Zongsheng Precision Mould Co., Ltd.
Contact: Mr. Nie 13923298099 (Wechat same number).
Miss Jia 15820657628 (Wechat same number).
Tel: 0757 2226 9630.
0757 color 22269276.
Fax: 0757 2226 9631 22269276.
Web site: en.fszongsheng.com.
Add: no. 1, Rongye 6 road, Fengxiang industrial zone, Daliang, Shunde district, Foshan city, Guangdong province
1. Test on the mould device of plastic bottle cap.
The test model is a very crucial content in the production process, and its modification to make up for it is the continuous development of the plan.
2. Prepare for the warm-up activities.
Actively test the plastic bottle cap mold and related equipment before the test.
To analyze whether its closeness is reasonable, to see whether it can be kept in common with the relevant scale and form of the equipment, to analyze whether the pores between the parts in the plastic bottle cap mold are reasonable, and whether there is a card slot.
The effect drawing of the plastic cover mold should ensure that its movement is very convenient, and the stability should be good, and the positioning of the initial orientation should be accurate.
All inserts should be fixed to avoid loosening.
All the pipeline joints and valves should be fully equipped, and the injection should be tested in the direction, and the waterway and other lines and moving parts should be analyzed to ensure its reasonable operation.
3. About devices and tests.
(1) the device shall be the same as the rules of the drawing.
(2) when the plastic bottle cap mold slides laterally, it should be in common with the horizontal plane.
(3) if there is a big difference between its scale length and width, make sure that the longer one is the same as the horizontal one.
(4) if there is an oil circuit and some other lines connecting to the number one time, it should be put on the side of inactivity to avoid adverse phenomena caused by the time of activity. In general, the rules in the injection machine are the use of screws and so on.
Usually use four to eight pressure plates, and set symmetrically.
After putting it into the injection equipment, it is necessary to adjust it. Its significance is to analyze whether all the moving equipment in the plastic bottle cap mold is stable and whether the positioning of the original parts can play its due benefits. We should pay attention to the following matters in detail.
The main results are as follows: (1) to ensure that there can be no pores between the parting surfaces of the plastic bottle cap mold, and there should be a great force to ensure its effective closeness.
(2) it is necessary to ensure that the movement of the oblique push rod and other guide parts is stable, that there are no dryness and problems, and that the time of positioning should be accurate and reasonable.
(3) when opening the mold, it is necessary to ensure that the products are stable, and push the pictures of the crystal easy-to-pull moulds in the plastic parts and pouring system into the plastic bottle cap mold, otherwise it will have a negative impact on it.
(4) ensure that the cooling water is clear, avoid leakage problems, and ensure that all valves operate in an orderly manner.
4. Try the mold.
After completing the device conditioning activities, you can take the test.
In detail, it is necessary to put in the material first, and then adjust the relevant values of the machinery.
To check whether the planning of the plastic bottle cap mold is accurate, and whether the sample is the same as the use of human rules.
Plastic bottle cap mold can be produced in large quantities.
In view of the adverse phenomena that may occur at this time, we should actively regulate and deal with them to ensure that they conform to the rules of the users.
Foshan Shunde Zongsheng Precision Mould Co., Ltd.
Tel: 0757 Tel: 22269630 / 13923298099 (Mr. Nie).
Web site: www.fszongsheng.com.
Add: no. 1, Rongye 6 road, Fengxiang industrial zone, Daliang, Shunde district, Foshan, Guangdong
Wechat official account
Mobile phone official website